[Glass] Seaside 3.1.1 in GemStone 3.1.0.5?

[Paul DeBruicker]

Thanks Johan.  That seems to have fixed it.


Paul



Johan Brichau-3 wrote
> Hey Paul,
> 
> Opening up the ConfigurationOfSeaside3, I think I spotted the problem.
> Can you load my latest commit and try again?
> 
> If it's not working, I will have to dig a bit deeper.
> 
> Johan
> 
> On 14 Feb 2014, at 21:11, Paul DeBruicker <

> pdebruic@

> > wrote:
> 
>> Hi Johan,
>> 
>> Thanks for the info.  
>> 
>> Is there a way to use 3.1.x on GemStone without having to remove the
>> Seaside
>> loading instructions on GemStone from all of the Configurations a project
>> may depend upon?
>> 
>> 
>> If I load Seaside using the github instructions then load my
>> configuration I
>> get a conflict error between the Seaside baseline and configuration.
>> 
>> 
>> 
>> Thanks again
>> 
>> Paul
>> 
>> 
>> 
>> 
>> Johan Brichau-3 wrote
>>> Hi Paul,
>>> 
>>> In Gemstone, the Seaside-Core package is not loaded. Instead, the
>>> Gemstone
>>> port Seaside-Core.gemstone is loaded.
>>> I added the 3.1.1 version as the #development version but it was not
>>> (yet)
>>> intended for Gemstone actually.
>>> 
>>> Loading Seaside 3.1 for gemstone now only works using the load
>>> instructions on github. 
>>> I'm close to wrapping up the ConfigurationOfSeaside3 though. I will take
>>> a
>>> look over the weekend.
>>> 
>>> Johan
>>> 
>>> On 14 Feb 2014, at 20:45, Paul DeBruicker <
>> 
>>> pdebruic@
>> 
>>> > wrote:
>>> 
>>>> Hello,
>>>> 
>>>> Inside my project’s configuration I’m attempting to load Seaside 3.1.1
>>>> into GemStone 3.1.05 and it fails with this error: 
>>>> 
>>>> 
>>>> ...RETRY->Seaside-Core-pmm.809
>>>> ...RETRY->Seaside-Core-pmm.809
>>>> ...FAILED->Seaside-Core-pmm.809
>>>> 
>>>> 
>>>> in the github-cache the metacello version info shows that the ‘version’
>>>> of Seaside-Core to be pmm.809 so I’m not sure why it can’t find it. 
>>>> I’ve
>>>> attached the transcript output from the load.  
>>>> 
>>>> 
>>>> In my configuration I haven’t updated or changed the spec references
>>>> for
>>>> Seaside in GemStone. They still point to the ConfigurationOfSeaside3 on
>>>> smalltalkhub.   I only changed the version from ‘3.0.10’ to ‘3.1.1’. 
>>>> Should I change it to point to the BaselineOfSeaside3?  If so what is
>>>> the
>>>> right way to make that change?  What else should I look at?  
>>>> 
>>>> 
>>>> Things load fine if I follow the instructions on
>>>> github.com/glassdb/Seaside31 but not if Seaside only a part of the
>>>> project I’m loading.  
>>>> 
>>>> 
>>>> Thanks
>>>> 
>>>> Paul
>>>> 
>>>> 
>>>> 
>>>> 
>>>> 
>>> 
> <seaside31-on-gemstone-3105.rtf>
>>> _______________________________________________
>>>> Glass mailing list
>>>> 
>> 
>>> Glass at .gemtalksystems
>> 
>>>> http://lists.gemtalksystems.com/mailman/listinfo/glass
>>> 
>>> _______________________________________________
>>> Glass mailing list
>> 
>>> Glass at .gemtalksystems
>> 
>>> http://lists.gemtalksystems.com/mailman/listinfo/glass
>> 
>> 
>> 
>> 
>> 
>> --
>> View this message in context:
>> http://forum.world.st/Glass-Seaside-3-1-1-in-GemStone-3-1-0-5-tp4743869p4743873.html
>> Sent from the GLASS mailing list archive at Nabble.com.
>> _______________________________________________
>> Glass mailing list
>> 

> Glass at .gemtalksystems

>> http://lists.gemtalksystems.com/mailman/listinfo/glass
> 
> _______________________________________________
> Glass mailing list

> Glass at .gemtalksystems

> http://lists.gemtalksystems.com/mailman/listinfo/glass





--
View this message in context: http://forum.world.st/Glass-Seaside-3-1-1-in-GemStone-3-1-0-5-tp4743869p4743882.html
Sent from the GLASS mailing list archive at Nabble.com.